UltraMount is a complete CB antenna Kit for the new Jeep Wrangler JK (2007+) that looks like a genuine factory accessory.
Cool Tech's new UltraMount Kit is a COMPLETE CB antenna solution with every element designed specifically for the new, 2007 Jeep Wrangler JK. There is no drilling of your body or sheetmetal required! (You will place a small hole in your plastic license plate assembly to facilitate attaching the antenna to the concealed UltraMount.)
Everything you need is included and each part has been planned to facilitate an easy installation and years of trouble-free service. With traditional CB mounts, it is frequently a challenge to route the coax into the vehicle. Done improperly, this can cause leaks, wind noise and just plain ugly aesthetics. With the UltraMount, the mount and coax routing is COMPLETELY hidden. But routing an antenna coax is a pain too, right? Not so with the UltraMount. The routed end of the coax has a very trick mini-UHF connector with an outside diameter almost the same as the coax itself. Follow the highly illustrated instructions (included) and route this coax end through a factory 2" grommet. After routing the coax up to the dash, simply screw on the supplied PL-259 connector. This makes routing a breeze and there is absolutely NO SOLDERING required! The all stainless steel mount is completely contained within the license plate assembly. Traditional CB antenna mounts are exposed - increasing vulnerability to theft and mischief. Included in this complete kit is a very unique, completely hidden CB antenna mount, a FireStik FL-4 4' fiberglass antenna (with tunable tip), 18' coax and connectors, and detailed instructions for installing it in your new 2007+ Wrangler. The mount fits all 2-door and 4-door 2007+ Wranglers!

UltraMount is a blend of a superior design with top quality components. All aspects of the UltraMount have been carefully engineered for ease of installation and years of reliabe service.

Some of the key features include;
1. Stainless Steel Bracket - Some vendors offer brackets in less expensive steel construction with a powdercoated finish. The problem with quality powdercoats is that ther are a very effective insulator. Fundamentally, an antenna bracket needs to provide a good conduct to ground. The UltraMount's all stainless construction combines superior conductivity along with proven longevity.
2. The UltraMount is a complete kit. You do not have to shop seperately for a mount, mounting hardware, coax, and antenna and then hope everything works well together. Some antenna are too heavy for some mounts and other antennas may be too thin and can "wag" continuously when your jeep is at speed. The UltraMount kit is packaged with one of FireStik's most recent antennas and has been tested under all conditions on a Jeep Wrangler JK.
3. The included Firestik antenna is a state-of-the-art 4' fiberglass shaft antenna with a tuneable tip. With the UltraMount kit you can tune the SWR reading to a very,very low level allowing you to get the maximum range from your CB.
4. Often times, mounting the antenna is only half the battle with traditional antenna installations. A challenging task is to find a suitable location to route the antenna wire and to thread it through sometimes challenging areas. This has been solved with the UltraMount. On one end of the cable you have FireStik's revolutionary FireRing. On the opposite end,the coax is "bare" as the connector is shipped seperately. Route the wire using the supplied instructions (super easy!) and simply screw on the supplied PL-259 connector. Solder the tip and you're done!
5. Speaking of coax routing - both the antenna bracket and the coax routing are completely concealed. There is a much reduced chance of vandalism or an unlucky contact with a tree branch, brush or shrub while 4-wheeling.
6. The UltraMount locates the antenna in an ideal, factory-like location. When you decide to upgrade your Wrangler with aftermarket bumpers, tire carriers, racks, etc., you can be assured that your CB mount won't get in the way.
7. Finally, each UltraMount is shipped with detailed, highly illustrated instructions. Mounting your new antenna and routing the cable up to your CB should take no more than 30 minutes!




